NEW Full Housing Shell Cover Case Pack with Screwdriver for Nintendo Gameboy Classic/Original GB DMG-01 Repair Part-Gray. 3.3 out of 5 stars 10. 99 $13.99 $13.99. $3.99 shipping. 1 Pair Conductive Rubber Button Pads for Original Nintendo Game Boy DMG-01 by Atomic Market. By Atomic Market. To begin, remove all 6 tri-wing screws from the back of your original Game Boy DMG-01. Keep these in a safe place as you will need them later when reassembling. Remove the ribbon cable connecting the front PCB (logic board) to the back PCB in a gentle downwards motion. At this point you should have the front and the back unit’s separated.

• Gameboy Dmg 01
• Original Gameboy Advance

Aug 12, 2018  Original Gameboy DMG-01. I wanted to see if I could use hot air to replace the screen. I show you how I go about removing and soldering back on the Gameboy LCD screen. AM Computers is. NEW Full Housing Shell Cover Case Pack with Screwdriver for Nintendo Gameboy Classic/Original GB DMG-01 Repair Part-Gray. 3.3 out of 5 stars 10. 99 $13.99 $13.99. $3.99 shipping. 1 Pair Conductive Rubber Button Pads for Original Nintendo Game Boy DMG-01. The Game Boy released on April 21, 1989 in Japan, followed by North America on July 31, 1989, and lastly in Europe on September 28, 1990. It is characterized by a large grey casing and model number DMG-01.

The original internal code name for the Game Boy was 'Dot Matrix Game', and the initials DMG came to be featured on the final product's model number: 'DMG-01'. Internal reception of the console at Nintendo was initially very poor; the DMG even received the derogatory nickname 'DameGame' from Nintendo employees, with dame (だめ) being Japanese for 'hopeless' or 'lame' in that context. Item 1.restored. original nintendo game boy dmg-01 handheld console.new glass lens.restored. original nintendo game boy dmg-01 handheld console.new glass lens. $75.99. Free shipping.

I was inspired by the many Game Boy Zero builds on You Tube, but one in particular where the user used an original Game boy cart to house the micro SD card. I give the user props for a good functioning build, but with my ability to design PCBs and some more knowledge about getting hardware working I set out to build my own. My project is all working in prototype form except for the audio at this point because i didn't buy an audio amp board for prototyping.
What I did is design a set of custom PCBs to replace the original GB PCBs and clean up the project significantly. Even though i was capable of designing the battery charger and audio amp circuits myself, I took the lazy route and leveraged some readily available designs from Adafruit and copied the Layout and schematics into my project.
Specs,
Original Game Boy DMG-01 Case.
Custom Main PCB

Gameboy Dmg 01

Custom Cart PCB
Custom Button PCB with extra X - Y buttons.
Adafruit 3.2' SPI TFT screen
Mono 2.5W amplifier Circuit
2000mA hour LiPo Battery
Battery Charger circuit
Main PCB
Holds the Pi Zero in a cut out in the middle of the board. Bridges the Connections over to the Cart header for the Mircro SD card. Also bridges the required pins from the GPIO to the screen header. Has Micro USB port for charging. Has USB-A port for external devices. Holds the battery charger circuit and audio amp circuit. I will be using the basic PWM out gpio pin for audio. the audio on these games are pretty crude anyways. The battery connector sticks through one of the openings in the battery compartment with some modification to the opening. I decided not to try to bring out the HDMI port as it would have been very complicated and using a SPI screen the output of the HDMI is the same very low resolution of the built in screen. I am also using the extra GPIO pins for the buttons instead of using a USB device like the teensy. this eliminates the need for a USB hub if you want a USB port on the outside.
Cart PCB
replaces the cart board with a custom board that holds the Micro SD card. Replaces the card edge connector with a female 0.1 pin header. I will post pictures of the board layout software, but the actual implementation will become more clear once I have the boards on monday.
Button PCB
There were existing options for the DMG-01, but they only had A and B buttons, I used the super game girl board at first for prototyping, but it wasnt really designed for the DMG GB even though it was based on the original 2 button PCB--ABXY button pads didn't line up. I decided to make my own board specifically for the DMG GB with the extra X and Y buttons. I am selling the extra boards on Ebay. I received them today and have pictures.
http://www.ebay.com/itm/231974209588?ss .. 1555.l2649

Original Gameboy Advance

Pictures and video.
Video of GPIO mapped buttons and Adafruit screen working in Prototype form.
https://www.youtube.com/watch?v=GM_RlXi .. e=youtu.be
Main board and Cart board Panelized (Layout Software screen shot)
Button Board PCB

Check items to add to the cart or select all

1. Add to Wishlist
2. Add to Wishlist
3. Add to Wishlist

Details

This kit contains all parts necessary to replace the miniature electrolytic capacitors in the original Game Boy handheld, model DMG-01.

For capacitor lists and maps, please see our Game Boy DMG-01 Wiki page.

Mar 12, 2019  The construction quality of both models has a different approach, the BGVP DMG has heavy duty metal built earpieces while the BGVP DM6 is made of resin. This grants a more robust build to the DMG and a super light weighted one to the DM6. Mar 14, 2019  Ok, I am making a final effort to explain to everyone how things work, regarding the 'fake shippings', and everything else in general. First of all, we know about the demand, and the amount of orders for the BGVP DM6. Every order on aliexpress has a default 5. Dec 03, 2018  having used the DMG and DM6 for a few weeks now, I can say that the DM6 has that rich full sound, meanwhile the DMG has a more V shaped sound, you can EQ it but it can't quite reach the DM6 signature, but I can see if someone prefers the DMG sound, in any case, BGVP has two hits in their hands, can't wait for their future products. Bgvp dm6 vs dmg. Sep 05, 2018  Introduction BGVP is a Chinese brand that produces in-ear monitors (iems) and earbuds. They are known for their Sidy iems and have produced other iems such as YSP04 and DGS100. Recently, they have released the DM6. I would like to thank BGVP.

Product history:
2019-10-13 - 1uf caps change to 3mm⌀ to for improved case closure

Additional Information

Compatible Hardware	Nintendo Game Boy (DMG-01)

Unless noted in the description, all Console5 products are fully tested and guaranteed. Cap kits are made using name brand, high quality, high-temp parts from Nichicon, Panasonic, and other reputable companies.